Texas water heater specialists
Across Austin & Travis County
Written quote before we start
Nights, weekends & holidays
Signs You Need Leaking Water Heater Repair
If any of these sound familiar, it's time to call:
- Puddle under or around the water heater
- Drip from the temperature-pressure relief valve
- Moisture on supply lines or fittings above the unit
- Water stains on the wall or ceiling below an attic unit
- Hissing sound near the tank
How Our Leaking Water Heater Repair Service Works
A clear, professional process — no guesswork, no surprises.
1Source identification
We trace the leak precisely — tank body, fittings, valves, or condensation — because the fix depends entirely on the source. We also test the temperature-and-pressure (T&P) relief valve, a common hidden leak source.
2Safety check
We verify the T&P valve, shutoff valves, and pan drain all function; a leak with no working safety valve is urgent.
3Targeted repair
Valves, nipples, supply lines, and drain valves are replaced; connections re-sealed with proper thread compounds.
4Honest verdict
If the tank itself is fractured or rusted through, we show you and quote replacement — no patch jobs on dead tanks.
When a permit is required, the City of Austin Development Services Department issues it, and the install must pass inspection.
What Does Leaking Water Heater Repair Cost in Austin?
Leak repairs in Austin most commonly run $180–$450: valve replacements and re-piped connections on the low end, supply-line and multi-fitting work higher. If the tank is ruptured, we'll quote replacement instead of selling you a repair that won't hold.
Diagnostic visits are credited toward the repair or replacement when you proceed with us the same day.
Repair vs. Replace: Our Honest Take
Our rule of thumb: if a repair costs less than half of replacement and the tank has life left, repair wins. That's the case more often than most companies admit.
Replacement makes sense for ruptured tanks, 12+ year units, and situations where efficiency gains pay for the upgrade. We lay out both options with honest math.
You make the call — we just make sure you have the full picture first.
What to Expect During Your Visit
Expect a text when we're on the way, shoe covers at the door, and a clear explanation before any work begins. We photograph our work, test every safety control, and review maintenance tips before we leave.
Austin-Specific Notes
Attic water heaters are everywhere in Austin — and attic leaks destroy ceilings fast. We treat every attic leak as urgent, and we install proper pans with drains (not just pans) so the next drip goes outside, not into your drywall.
Related Services
Often booked together with leaking Water Heater Repair:
We offer this service across Austin and Travis County, including water heater service in Bee Cave, water heater service in Spicewood, water heater service in Lago Vista.
The leak clock: what happens while a leak sits
A small leak rarely stays small. Here is what usually happens while it sits, and why acting early keeps the repair small.
- First hours: water spreads across the floor and fills the drain pan. Flooring starts to wick moisture, and anything stored nearby gets wet.
- First day: drywall and subfloor absorb water. A musty smell can appear, and the wet area keeps growing.
- 24 to 48 hours: mold can start to grow on wet drywall. The longer the material stays wet, the more likely growth becomes.
- After 48 hours: damage spreads into framing and flooring, and the repair scope grows with it. Early shutoff and a quick call keep the job small.
If the leak is active, shut off the water to the heater and call. The clock stops when the water stops.
When one problem brings another
A leak is often the first sign of a second problem. These combinations show up together, and each one changes the fix.
- Leak plus mold risk: water sitting on drywall for a day or two can start mold growth. Drying the area matters as much as fixing the leak.
- Leak plus slab line: if the water is not coming from the tank, the buried line under the slab may be leaking. Pinpoint detection tells the two apart.
- Tankless plus scale: on tankless units, hard water scale causes weak flow and error codes that look like failure. A descaling flush is the first step, not a new unit.
- Old tank plus corrosion: once the anode rod is gone, the tank rusts from the inside. A corroded tank with a leak is usually a replacement, not a repair. See anode rod replacement for how the rod protects the tank.
Need Leaking Water Heater Repair?
One call and we're rolling. Same-day service across Austin.
Call +1 (512) 352-9665FAQs About Leaking Water Heater Repair
Straight answers from our technicians.